Installation Instructions · Publication 5069-IN003 · Rockwell Automation

Compact 5000 I/O EtherNet/IP Adapters 5069-AENTR Installation Guide

This document provides installation instructions for the Compact 5000 I/O EtherNet/IP adapters, catalog numbers 5069-AENTR and 5069-AENTRK. It covers DIN rail mounting, RTB wiring for MOD and SA power, IP address configuration, EtherNet/IP network connection, and module installation. The adapters are configured with the Studio 5000 Logix Designer application and support up to 31 Compact 5000 I/O modules per bank.

Download PDF
31 Max I/O Modules Supported
0…60 Operating Temperature
10 A @ 18…32V DC MOD Power Bus Max Current
10 A @ 18…32V DC or 10… SA Power Bus Max Current

Document Preview

Open the full PDF in a new tab  · Publication 5069-IN003

Specifications

Voltage and Current Ratings

MOD power 220 mA @ 18…32V DC
MOD power inrush 1750 mA for 70 ms
MOD power passthrough 9.78 A @ 18…32V DC
SA power (DC) 5 mA @ 0…32V DC
SA power (AC) 2 mA @ 0…240V AC, 47…63 Hz; Ex, 125V AC Max
SA power passthrough (DC) 9.95 A @ 0…32V DC
SA power passthrough (AC) 9.975 A @ 0…240V AC, 47…63 Hz; Ex, 125V AC Max

Temperature

Operating temperature 0 °C ≤ Ta ≤ +60 °C (32 °F ≤ Ta ≤ +140 °F)
Surrounding air, max 60 °C (140 °F)
Vertical mount derating 30% of max Ta; max 42 °C (108 °F)

Isolation Voltage

SA and MOD power to Backplane 300V continuous, Basic Insulation; type tested at 1500V AC for 60 s
SA to MOD power 300V continuous, Basic Insulation
Ethernet to Backplane 300V continuous, Basic Insulation
Ethernet to MOD power 300V continuous, Double Insulation; type tested at 4242V DC for 60 s
Ethernet to SA power 300V continuous, Double Insulation; type tested at 4242V DC for 60 s
Between Ethernet ports No isolation

Wiring

RTB wire size (screw and spring) 0.25…2.5 mm2 (22…14 AWG) solid or stranded copper, rated 105 °C (221 °F), single wire only
Grounding wire size 2.5 mm2 (14 AWG) solid or stranded copper, rated 105 °C (221 °F), 3.5 mm max diameter including insulation
Insulation-stripping length 10 mm (0.39 in.)
Terminal block torque 0.5…0.6 N•m (4.4…5.3 lb•in)

Overcurrent Protection (Recommended External)

MOD power 10…12 A @ 22.5…43.2 A2t, Fast Acting
SA power 20 A @ 250V AC

Temperature Codes

North American temp code T4
UKEX/ATEX temp code T4
IECEx temp code T4

Physical

Enclosure type rating None (open-style)
Adapter dimensions (W x H x D) 59.56 mm x 139.00 mm x 105.30 mm (2.34 in. x 5.47 in. x 4.15 in.)
Compatible DIN rail EN50022 35 x 7.5 mm or EN50022 35 x 15 mm, zinc-plated chromate-passivated steel

Catalog Number Format

How to read an Allen-Bradley 5069 catalog number. Each position encodes a specific configuration attribute.

Position
Meaning
Example
Base catalog number
Compact 5000 I/O EtherNet/IP Adapter with dual embedded switch ports
5069-AENTR
Suffix K
Conformal coating option
5069-AENTRK

Communication Protocols

Supported industrial networks and field buses for the products covered by this publication.

EtherNet/IP Dual RJ45 ports on the bottom of the adapter; supports 10/100/1000 Mbps cabling per IEC 61918 and IEC 61784-5-2. IP address configurable via rotary switches (192.168.1.x last octet), DHCP server, BOOTP DHCP EtherNet/IP Commissioning Tool (v3.02.00 or later), or RSLinx Classic.

Certifications & Compliance

CL I, DIV 2, GP A, B, C, D (North American Hazardous Location) II 3 G, Ex ec IIC T4 Gc — UKEX Regulation 2016 No. 1107, certificate UL22UKEX2494X II 3 G, Ex ec IIC T4 Gc — ATEX Directive 2014/34/EU, certificate DEMKO16ATEX1758X IECEx, Ex ec IIC T4 Gc — IEC 60079-0 / IEC 60079-7, certificate IECExUL16.0124X Pollution Degree 2, Overvoltage Category II per EN/IEC 60664-1 Altitude up to 2000 m (6562 ft) without derating

Document Contents

Full PDF covers the following topics in detail:

  • About the Adapters (status indicators, ports, connectors overview)
  • Install a Compact 5000 I/O System (components needed, system planning, spacing, dimensions)
  • Set the Network Internet Protocol (IP) Address (rotary switches, DHCP, BOOTP, RSLinx)
  • Install the Adapter (DIN rail mounting procedure)
  • Install the RTB
  • Wire the RTB (MOD power, SA DC power, SA AC power, disconnect wires)
  • Connect an EtherNet/IP Network (RJ45 pinout, port connections)
  • Install Compact 5000 I/O Modules
  • Install the End Cap
  • Power the System
  • Remove the Adapter
  • Specifications
  • Additional Resources

Frequently Asked Questions

How many I/O modules can a single 5069-AENTR adapter support?
The adapter can communicate with as many as 31 local Compact 5000 I/O modules installed to its right on the DIN rail.
How do I set the IP address using the rotary switches?
The adapters ship DHCP-enabled with rotary switches set to 999. If the network uses 192.168.1.x, turn the three rotary switches to the desired last octet value (001…254) before installing the adapter. At powerup the adapter sets its IP to 192.168.1.xxx, subnet mask 255.255.255.0, and gateway 0.0.0.0. For other network ranges, leave the switches at 999 and use a DHCP server, BOOTP DHCP EtherNet/IP Commissioning Tool (v3.02.00 or later), or RSLinx Classic software after powerup.
Does the 5069-AENTR support Removal and Insertion Under Power (RIUP)?
No. The adapter does not support RIUP. Power must be removed before inserting or removing the adapter or connecting/disconnecting the RTB or communication cable.
What power supplies are required, and can one supply serve both MOD and SA power?
The adapter requires separate external power supplies for MOD power (system-side, 18…32V DC) and SA power (field-side, DC or AC). Rockwell Automation strongly recommends using separate supplies so that loss of one does not affect the other. The adapter itself has no embedded power supply. SELV-listed supplies are required when Functional Safety modules are connected.
What DIN rail materials are compatible with the adapters?
Use zinc-plated chromate-passivated steel DIN rail, either EN50022 35 x 7.5 mm or EN50022 35 x 15 mm. Aluminum, plastic, or other materials that corrode or oxidize can result in improper or intermittent grounding and are not recommended.
What is the operating temperature range, and does vertical mounting affect it?
The rated operating temperature is 0…60 °C (32…140 °F). When the DIN rail is mounted vertically, the operating ambient temperature must be derated to 30% of the maximum Ta, giving a maximum of 42 °C (108 °F).
What hazardous location certifications do the 5069-AENTR and 5069-AENTRK carry?
The adapters are approved for Class I, Division 2, Groups A, B, C, D (North American). They also carry UKEX (certificate UL22UKEX2494X) and ATEX (certificate DEMKO16ATEX1758X) approval as Equipment Category II 3 G, Ex ec IIC T4 Gc for Zone 2, and IECEx certification (IECExUL16.0124X) for Zone 2. The K suffix indicates conformal coating. In Zone 2 installations the adapter must be mounted in a certified enclosure with minimum IP54 ingress protection.

Disclaimer

Disclaimer: PLC Exchange is an independent reseller and is not an authorized distributor, affiliate, licensee, partner, or agent of Allen-Bradley / Rockwell Automation. All product information on this page is compiled from publicly-available manufacturer publications, technical data sheets, and catalog sources, each of which remains the copyright of its originating manufacturer. We make no representation or warranty, express or implied, regarding the accuracy, completeness, timeliness, or fitness for any particular purpose of the specifications or descriptions shown — content may contain errors, omissions, or out-of-date information. Product images are the property of their respective manufacturers, trademark owners, and source publications, and are displayed solely for identification purposes under the nominative fair use doctrine; images are representative and may depict a different configuration or catalog variant than the exact product listed. Purchasers should independently verify specifications against the current manufacturer publication before placing an order. All product names, trademarks, service marks, and registered trademarks are the property of their respective owners, and their use does not imply endorsement or affiliation.